AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |
Back to Blog
Sharpening drill bits3/24/2023 If you pursue sharpening small bits (< 1/ 8 in / < 3.0 mm), Minimum point angle on the Tormek DBS-22 Drill Bit Sharpening Attachment is 90°. One sharpener has used a precision pen vice (like the Starrett 166C ) with the Tormek DBS-22 to hold bits as small as wire number 61 (= 0.0390" ≈ 5/ 128" ≈ 1 mm).Ĭlearance angles based on drill bit size should be used.A pin vice can assist with reducing this flex.Ĭan't use the Tormek DBS-22 Drill Bit Sharpening Attachment with these bits - they are too large (See also Note 1, below)īits as small as 1/ 8 inch can be held in the Tormek DBS-22, but they can flex easily. Follow the proper instructions and see how the process is simple.Can't use the Tormek DBS-22 Drill Bit Sharpening Attachment with these bits - they are too small. The bench grinder is turning out to be less expensive, and they give you a straightforward approach to getting your tools ready for the next project. The sharpening drill bit is turning to be an efficient skill for anyone in the building industry or anyone planning to join. Rescue yourself using a sharp masonry drill. Drilling masonry materials is already an energy-sapping experience. The sharpening skills shared in this post are the common ones you can use to sharpen your masonry drill bits. The sharpeners are available in different sizes and shapes to suit your budget and masonry tool sharpening needs. Save money and time by sharpening the masonry drill is the use of a drill sharpener. The idea here is to make sure no material remains behind the cutting face leaving the cutting face to be the only place of the drill bit to cut. With the drill working at 60-degrees, this time feeds the grinding wheel in an incline, so the surface behind the cutting edge gets into contact with the grinding wheel first. Hold the drill between the thumb and forefinger.Grinding the edge will keep the drill from rubbing or rubbing on the material. After grinding the cutting face, the masonry drill should have clearance behind the cutting edge. The best practice would be to dip the drill bit into the water after every grinding burst.Īlso Read: 6 Types Of The Drilling Machine And Their Applications! Grinding the Drill Bit Clearance Face Use short bursts to grind the drill while using water to cool off the drill bit.Ensure that both cutting edges as similar as possible.Turn the over and repeat the sharpening process on the other cutting face.An alternative test would be to place two hex nuts and hold the drill in between. Use an angle gauge to check the drill bit, which should give at least 118 degrees.Make sure there are no chips or uneven places on the cutting edge. Check if the drill bit’s face is clean and has an even look.Push the masonry drill against the grinding wheel as you apply some pressure.The angle can be 60-degrees or thereabouts. Use the drill bit cutting edge as the drilling angle.Bring the drill bit up to 1 millimeter of the grinding wheel.Place the index finger of the right hand on the tool stop of the grinder.Turn on the grinder as you hold the drill bit between your fingers.Putting on gloves is not recommended because it may be trapped on the grinding wheel. At this point, you should have all your safety clothing. Make sure the holding position feels comfortable.Īlert: Be cautious when you pass hands near the high-speed grinding wheel. Hold the masonry bit about one inch from the drill’s tip and place the left hand on the shank of the drill.Hold the drill bit on both hands on the tips of your thumbs and forefingers, giving you the option of moving the drill in any direction.The clean water should be nearby, check if the bench grinder has a small container, but if you can use a plastic container, the better because the water stays cooler for longer.Bolt or clamp the bench grinder to stop unnecessary movements.Set the bench grinder on the workbench close to the edge that allows you to stand as you sharpen the drill.Clear the table and remove all flammable materials from the grinding area.Find enough space on your workbench where you can move your arms.6 Final Word Here Are Some Things That You Will Need
0 Comments
Read More
Leave a Reply. |